Cannon IntelliTroll Manual do Proprietário

INTELLITROLL SPEED-N-TEMP MONITOROwner’s Manual

8PROBE INSTALLATION (cont.)

9PROBE INSTALLATION (cont.)

10PROBE INSTALLATION (When NOT using the IntelliTroll Monitor)Both the Digi-Troll 5 and Digi-Troll 10 downriggers are compatible with the IntelliTroll

11PROBE INSTALLATION (cont.)4. With a 1/4” wrench, loosen the bolt and remove.5. Install the antenna spring that came with the Intellitroll sensor k

12PROBE INSTALLATION (cont.)6. Tighten bolt. Caution: Do not over tighten as the stainless steel bolt head may shear with too much torque.7. Once the

13PROBE INSTALLATION (cont.)8. Terminate cable as previously described.Your Digi-Troll is now Intellitroll compatible. Once you attach your Intellitr

14SYSTEM OPERATION On / Off of ProbeThere is no on / off switch for the IntelliTroll Probe. The probe automatically turns on when placed in the water

15SYSTEM OPERATION (cont.)Setup Items 1. Back Light (default off) • The back light will help make the display information visible in low light c

16SYSTEM OPERATION (cont.)On / Off of DisplayAs mentioned previously, the display can be turned on by pressing the POWER/ MENU button. Once the displ

17SPECIFICATIONSMonitor diagonal: 4 inchesMonitor resolution: 160V x 128HMonitor power consumption: 25mA with backlight off 55mA with ba

Serial Number: _____________________________________Purchase Date: _____________________________________Store Where Purchased: ______________________

18FAQ (cont.)Water in transmitter: 1. Water should not be in the transmitter. The O-ring seal design has been tested well beyond the limits of

19FAQ (cont.)No data is displayed when the trolling motor is turned on: 1. All electronic devices transmit unwanted signals. The receiver (monitor

2040501001101202030200260250270280290135140130109060708095210 5PARTS DIAGRAM

21PARTS LISTItem Part Number Description Qty Req’d10 3990220 (includes 20-30) ASSEMBLY, SNT SENSOR 120 802003 HDW PAD WHEEL 130 802014 HDW SHAFT .875”

22LIMITED WARRANTYJohnson Outdoors Marine Electronics, Inc. warrants to the original purchaser that if the accompanying product (see exclusions below)

23AFTER THE APPLICABLE WARRANTY PERIODAfter the applicable warranty period, or, if one of the above exclusions applies, Cannon® products will be repai

24ENVIRONMENTAL COMPLIANCE STATEMENT (cont.)most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Dire

Consumer & Technical ServiceJohnson Outdoors Marine Electronics, Inc.PO Box 8129121 Power DriveMankato, MN 56001Phone (800) 227-6433Fax (800) 527

1Congratulations on your purchase of the Cannon® IntelliTroll Depth, Temperature and Speed monitoring system. The probe unit and display use Cannon’s

2Here are a few tips:• Avoid mounting the display near 2 way radios and antennas as this can cause interference with probe operation.• If the moun

3To add an inline connector to your IntelliTroll system follow this procedure:You will need one each of the following Cannon components:• p/n 339750

4current failures.You can attach the power cable to the boat accessory panel, however you may experience undesirable electrical interference if you do

Step 5: Install the Coated Downrigger Cable NOTE: The coated cable may make certain spool-mounted cable counters inaccurate due to the difference in

6PROBE INSTALLATION (When using the IntelliTroll Monitor)Installing the BatteryUnscrew the back cover of the probe module and remove the plastic batte

7PROBE INSTALLATION (cont.)Installing Probe on the Downrigger cableTo prevent losing the probe overboard it is recommended that the safety lanyard cla